# Quick Answer: How Many Outlets Can I Put On A 20 Amp Breaker?

## How many outlets can one GFCI protect?

There’s no limit.

A standard GFCI will protect up to 20 amps, drawn from any combination of receptacles, either the built-in one or any number of additional ones connected to its load terminals..

## How many outlets can be on a breaker?

I’m ask so many times how many outlets and or lights can I put on a 15 amp or 20 amp breaker. Well NEC code does not have it listed that way. By rule of thumb you would stick with 8 to 10 outlets and or lights per breaker.

## Can you put lights and outlets on the same circuit?

Basic answer to your question of can a mixture of lights and receptacles be installed on a single circuit is yes.

## Can 14 gauge wire be used for outlets?

Yes you may use No. 14 AWG Cu wire for outlets but the Circuit Breaker to protect the circuit should be only 15A. Do not use 20A Circuit Breaker for this circuit. … The circuit should not have more than 10 receptacles.

## Can I put two GFCI outlets on the same circuit?

When you need to wire multiple GFCI outlets such as in a kitchen or bathroom you have a couple of options. To save money, you can put in a single GFCI and then wire additional standard outlets to the “LOAD” output from the single GFCI. This provides the same protection as having a GFCI at each location.

## How many LED lights can you put on a 20 amp circuit?

40 lightsYou can put up to 40 lights (based on 50 watt light) on a 20 amp breaker.

## Can I daisy chain electrical outlets?

You can daisy-chain a GFI just like a regular receptacle, with one difference. The incoming wires must connect to the “line” terminals while the outgoing wires must connect to “load.”

## How many receptacles and lights can I put on a 20 amp breaker?

10 receptaclesOne rule of thumb is to assign a maximum draw of 1.5 amps to each receptacle, which allows for 10 receptacles on a 20-amp circuit.

## What is code for electrical outlets in a basement?

Outlets must be installed at any wall space 24 inches or greater, within 6 feet of all wall breaks, and 12 feet thereafter. 2. All basement outlet openings must be protected by a listed combination type Arc-Fault Circuit Interrupter (breaker), except bathrooms and unfinished areas.

## How many 15 amp receptacles can be on a 20 amp circuit?

Table 210.21(B)(3) also shows that a 15 amp receptacle can be installed on a 20 amp circuit that serves 2 or more receptacles.

## Can you use 14 gauge wire on a 20 amp breaker?

You can not use 14 AWG anywhere on a circuit that has a 20A breaker. If you are putting 15 amp receptacles on a 20 amp circuit with 12 gauge wire, then you MUST use the screw terminals, not the back stab terminals. … Just use the side terminals.

## How far can you run 12 gauge wire on a 20 amp circuit?

You can run a 10 gauge wire up to 85 feet on a 20 amp circuit. If you opt to use this type of wire on a 15 amp circuit, it can run up to 115 feet. After these distances, the circuit will go over the recommended 3% voltage drop. You can run a 12 gauge wire up to 70 feet on a 15 amp circuit.

## Is it OK to mix 12 and 14 gauge wire?

12 is yellow. 14 is white. You can only install a larger wire upstream of a shorter wire. So if it goes circuit breaker -> 12ga -> 14ga, that’s fine.

## Will 12 gauge wire carry 20 amps?

12-gauge wire is the next size larger and is allowed to carry up to 20 amps. As a result, the amp rating of a circuit breaker has the following relation to the wire size that has been chosen. A 20-amp breaker is never* allowed to run any circuit whose wires (anywhere on the circuit) are 14-gauge.

## How many outlets can you put on a 14 2 wire?

12 outletseach outlet( receptacle, light) is roughly one amp so you can use 14-2 wire to 12 outlets protected by a 15 amp breaker.

## How long can you run 12 gauge wire?

A 12 gauge wire is typically good for 15 amp at 100 feet.

## How many outlets can I put on a 15 amp breaker?

Generally, homes have eight to 10 outlets on a 15 amp breaker but not all are used at the same time. Lights and outlets are normally wired on separate branch circuits, which means that the lights will be protected by a separate circuit breaker to the one which protects the outlets.

## How many lights can I put on one switch?

Most circuits in a home allow for 15 to 20 amps, so you can safely connect 1400 to 2400 watts of lighting on one light switch. That’s enough for 23 to 40 60-watt bulbs or 280 to 480 5-watt LEDs.