What Happens If You Don’T Break Your Subwoofer?

What does a blown Sub sound like?

Partial sound with distortion – When you hear a weak, distorted sound coming from your subwoofer, at any volume, you probably have a partially blown subwoofer on your hands..

What is better 2ohm or 4ohm subwoofers?

The kind of resistance that the sub has will determine the loudness and quality of bass you’ll get. … Basically, a 2 ohm subwoofer demands less power from the amp and tends to deliver louder bass. On the contrary, a 4 ohm subwoofer will demand more power from the amp and deliver less loud but higher quality bass.

Are 2 subs louder than 1?

It depends on how the coil of the subs handle power and on the mechanical aspects of the design as well. The 2 subs will probably be just a bit louder (you would need a meter to tell) because the single sub would be entering into power compression and becoming less efficient as you increase the power.

Why would a subwoofer smoke?

Clipped, unclipped, dirty, clean, it doesn’t really matter how the power goes into the woofer, it is going to cause the voice coil to heat up. … Both the smoke and the smell are a result of those resins on the coil returning to liquid and eventually a vapor.

Do I need to break in my subwoofer?

Do I need to break in my speakers or subwoofer(s)? The answer is no. While it is true that the suspension of a speaker will loosen up over time, there is no need to play a speaker at half power or low volumes for an extended period in order to aid or ease into this.

Do Subs smell when breaking in?

The ‘new sub’ thing is a BS myth. Yes some new subs require a break in period to loosen up the suspension for full movement, but when the break in period is properly done the subs won’t stink. If the sub stinks, you are hurting it.

How do I make my subs hit the hardest?

How to Make Subwoofers Hit HarderChoose the correct amplifier for the subwoofer. Every type of subwoofer requires a certain power output by an amplifier. … Install the subwoofer in a bandpass box. … Adjust the settings on the amplifier and stereo unit to accommodate the subwoofer.

What size subwoofer hits the hardest?

Generally speaking though, given sufficient power, two 10-inch subwoofers will produce a cleaner, harder-hitting bass thanks to its combined cone surface area creating more sound pressure.

Why is my sub making a popping noise?

So when you change inputs or change listening modes and you hear the subwoofer(or any speaker) “pop” this indicates that particular pre-out jack is not being muted….or not being muted for a long enough period of time. … This can indicate there is a failed diode / circuit in the receiver.

What volume should I set my subwoofer?

If you’re using the subwoofer in a stereo or computer system, just set the subwoofer volume so that it sounds the best from the chair you usually sit in to listen. The sound should be neither boomy nor thin. You can also change the subwoofer volume on the fly to suit whatever music or movies you’re listening to.

Do 10 or 12 subs hit harder?

Q: Which subwoofer will sound the deepest? … But, generally speaking, given adequate power, the two 10″ subs will sound a little cleaner and punch harder because their combined cone surface area yields more sound pressure. The single 12″ sub, however, may sound a little deeper.

Do subwoofers get hot?

These peaks and troughs correlate with the movement of a subwoofer. … When clipping is present the subwoofer moves less than normal due to the plateaus in the waveform and in turn causes excess heat to build up. Over time this excess heat causes the voice coil to break down and eventually fail.

What does it mean when a subwoofer is clipping?

Long term clipping is a result of inadequate RMS or continuous power available for the volume setting. … Subwoofers can overheat if not chosen properly, clipping the sound in a similar distorted manner when they fail to completely follow the original waveform even if the amplifier signal is accurate.

What happens if you don’t break your subwoofer?

What can happen if you skip breaking in your subs? If you don’t allow for a break in period you could run into one of the issues below: Burned or unwound coil: Burned or unwound coils can be caused by the buildup of excess heat and a distorted signal. Stiff spiders leave you with less suspension travel or excursion.

Do subs get louder after break in?

Subwoofers should not get louder as they break-in. … You may even find that your manufacturer does not recommend a break-in process and instead has other recommendations for playing various sounds when you initially use your subwoofer and other speaker equipment.

How long does it take to break in a subwoofer?

A good 10-12 hour break-in run—performed at a lower volume level than the aggressive level used for the dinner break-in but still moderately loud–completes the run-in process.

How do you break in new subwoofers?

0:30 So, the first thing you need to do is run extremely low bass through the subwoofer at moderate volume for about 15 to 20 minutes. Ease into it. Let the poor thing get warmed up and cycling. Don’t try and take a subwoofer out of the box, any manufacturers, and turn it right up to 10.